NEA Group

Enter your username and password here in order to log in on the website:
vcard Compression Systems Martina Frenz Head of Corporate Communications Werkstrasse o. Nr. 52531 Uebach-Palenberg Germany Tel: +49-2451-481-154

Challenge Boundaries

23. August 2017

This classfier will be exhibited at the POWTECH in Nuremberg (26-28 Sep 2017). Join us in Hall 4A - BOOTH 325!

The new GRC air classifier provides revolutionary results

An important feature of plastics is that their properties such as formability, hardness, elasticity, and strength or temperature resistance vary when additives and fillers are admixed and can be adapted to the needs of the respective application, whereby additives are normally being applied in smaller quantities. Filling materials are primarily extenders which replace expensive raw materials with less costly ones for plastics production. However, some of these also improve various final product properties.

The most frequently used filling materials for plastics are calcium carbonate and talc powder. Calcium carbonate improves the mechanical strength properties and the weathering resistance while talc powder improves stiffness and resistance to thermal distortion.

The particle size distribution of a filling material is a decisive factor for the properties of a plastic. When manufacturing the filling materials, a precisely defined particle size distribution is achieved by grinding and subsequent separation, the so-called classification.

This classification step of the particles is a general requirement after grinding in a mill. While it is preferred to integrate the separation process into the mill itself, external air classifiers are commonly being used. Such is the case especially with ball mills.

Classification of solids with GRC air classifiers

Even prior to grinding, the use of an air classifier can be advantageous. If the feed material for the grinding process already contains a large quantity of desired final product, it makes sense to separate the fine material fraction in advance. Firstly
this material no longer burdens the mill and secondly overgrinding of such material is being avoided.

The NEUMAN & ESSER (NEA) air classifier GRC (Guide Ring Classifier) is such an air classifier allowing both types of above mentioned operations.

The initial GRC layout was designed for the classification of roughly 200 μm to 20 μm (1 μm = 0.001 mm) particles.

The air classifier divides the so-called feed material into fine material on one side and coarse material on the other side. The size GRC 820 at the NEUMAN & ESSER Test Center achieves throughputs of several tons per hour for medium fineness. For classification in the higher fineness range, throughput is reduced to several hundred kilograms per hour because the number of particles to classify increases exponentially: if 0.1 mm sized particles are crushed to 0.01 mm, the number of particles increases thousand-fold at the same time.

The feed material is fed into the GRC from the top using a vertical pipe. After falling onto a distribution plate above the classifier wheel the material is thrown to the outer diameter of this plate. There, the material drops into a ring gap between the classifier wheel on the inside and the air guidance ring on the outside.

The inflowing air now carries the particles into the classification zone. Here fine particles are allowed to pass whereas too large particles are being rejected.

After passing the classifier wheel the fines leave the classifier housing directly beneath the classifier heading for the downstream filter where the finished product is being discharged from the system.

The rejected fraction drops to the bottom of the housing and leaves it via a discharge airlock.

Multiple improvements provide a revolutionary result

In order to improve the already existing high performance, NEUMAN & ESSER has now made essential improvements to the GRC air classifier.

Ideally a perfect classifier allows only a very specific size of particle and below to pass. Since this is technically not feasible on a production scale the range of particle size above and below the target value defines the quality of such a classifier; the so called “cut efficiency”. The smaller the range, the better the classifier.

NEA experts focused on how to intensively separate fine and coarse in the feed material, dispersing as it is called by the experts and on efficiently guiding the material through the GRC classification process.

Only if the solids exist as individual particles in the classifying zone, the classifier can effectively remove the desired fraction from the feed material, thus classifying two precisely defined partial quantities.

The new GRC design features now a distribution cone in the inlet of the feed material above a significantly redesigned dispersing unit. After sliding down the cone and passing the dispersion zone, the material reaches the known ring gap. In contrast to the former design now a virtuously engineered guide vane ring handles the transportation into the direction of the classification zone.

Extensive and detailed testing with the new NEA classifier revealed an unexpected magnitude of improvements not only in yield, throughput and energy consumption but also in the range of achievable fineness. The new design now allows widening the possible fineness range from 200 μm to 2 μm instead of 20 μm!

Different sizes of the revolutionary new GRC air classifier are available for various throughputs nd applications not only in plastics but also for minerals, paints and coatings, in the chemical sector or for applications in the food industry, wherever they are needed.